Extract and count

First step in the analysis is to import the data (see Import Sequencing Data).

The next step is to extract and count the small RNAs to create a small RNA sample that can be used for further analysis (either annotating or analyzing using the expression analysis tools):

        Toolbox | Transcriptomics Analysis (Image expressionfolder) | Small RNA Analysis (Image small_rna_folder) | Extract and Count (Image count_small_rna)

This will open a dialog where you select the sequencing reads that you have imported. Click Next when the sequencing data is listed in the right-hand side of the dialog. Note that if you have several samples, they should be processed separately.

This dialog (see figure 26.16) is where you specify whether the reads should be trimmed for adapter sequences prior to counting. It is often necessary to trim off remainders of adapter sequences from the reads before counting.

Image small_rna_count_step2
Figure 26.16: Specifying whether adapter trimming is needed.

When you click Next, you will be able to specify how the trim should be performed as shown in figure  26.17.

Image small_rna_count_step3
Figure 26.17: Setting parameters for adapter trim.

If you have chosen not to trim the reads for adapter sequence, you will see figure 26.18 instead.

The trim options shown in figure 26.17 are the same as described under Adapter trimming. Please refer to this section for more information.

It should be noted that if you expect to see part of adapters in your reads, you would typically choose Discard when not found as the action. By doing this, only reads containing the adapter sequence will be counted as small RNAs in the further analysis. If you have a data set where the adapter may be there or not you would choose Remove adapter.

Note that all reads will be trimmed for ambiguity symbols such as N before the adapter trim.

Clicking Next allows you to specify additional options regarding trimming and counting as shown in figure 26.18.

Image small_rna_count_step4
Figure 26.18: Defining length interval and sampling threshold.

At the top you can choose to Trim bases by specifying a number of bases to be removed from either the 3' or the 5' end of the reads. Below, you can specify the minimum and maximum lengths of the small RNAs to be counted (this is the length after trimming). The minimum length that can be set is 15 and the maximum is 55.

At the bottom, you can specify the Minimum sampling count. This is the number of copies of the small RNAs (tags) that are needed in order to include it in the resulting count table (the small RNA sample). The actual counting is very simple and relies on perfect match between the reads to be counted together26.3. This also means that a count threshold of 1 will include a lot of unique tags as a result of sequencing errors. In order to set the threshold right, the following should be considered:

Clicking Next allows you to specify the output of the analysis as shown in 26.19.

Image small_rna_count_step5
Figure 26.19: Output options.

The options are:

Create sample
This is the primary result showing all the tags and respective counts (an example is shown in figure 26.20). Each row represents a tag with the actual sequence as the feature ID and columns with Expression values, Length, and Count. Expression values and the actual count are based on 100 % similarity26.4. The sample can be used in further analysis by the tools of the Transcriptomics Analysis toolbox in the "raw" form, or you can annotate it using the Annotate and Merge Counts tool. The tools for working with the data in the sample are described in Working with the small RNA sample. Note that when small RNA samples are used for setting up and experiment, it is always the Expression values that will be used.
Create report
This will create a summary report as described below.
Create list of reads discarded during trimming
This list contains the reads where no adapter was found (when choosing Discard when not found as the action).
Create list of reads excluded from sample
This list contains the reads that passed the trimming but failed to meet the sampling thresholds regarding minimum/maximum length and number of copies.

Image smallrnasample
Figure 26.20: The tags have been extracted and counted.

The summary report includes the following information (an example is shown in figure 26.21):

Trim summary
Shows the following information for each input file:
  • Number of reads in the input.
  • Average length of the reads in the input.
  • Number of reads after trim. The difference between the number of reads in the input and this number will be the number of reads that are discarded by the trim.
  • Percentage of the reads that pass the trim.
  • Average length after trim. When analyzing miRNAs, you would expect this number to be around 22. If the number is significantly lower or higher, it could indicate that the trim settings are not right. In this case, check that the trim sequence is correct, that the strand is right, and adjust the alignment scores. Sometimes it is preferable to increase the minimum scores to get rid of low-quality reads. The average length after trim could also be somewhat larger than 22 if your sequenced data contains a mixture of miRNA and other (longer) small RNAs.
Read length before/after trimming
Shows the distribution of read lengths before and after trim. The graph shown in figure 26.21 is typical for miRNA sequencing where the read lengths after trim peaks at 22 bp.
Trim settings
The trim settings summarized. Note that ambiguity characters will automatically be trimmed.
Detailed trim results
This is described under Adapter trimming.
Tag counts
The number of tags and two plots showing on the x-axis the counts of tags and on the y-axis the number of tags for which this particular count is observed. The plot is in a zoomed version where only the lower part of the y-axis is shown to make it possible to see the numbers of tags higher counts.

Image extractandcountreport
Figure 26.21: A summary report of the counting.



Footnotes

... together26.3
Note that you can identify variants of the same miRNA when annotating the sample.
... similarity26.4
Note that you can identify variants of the same miRNA when annotating the sample.