Identify variants and add expression values

The Identify Variants and Add Expression Values ready-to-use workflows can be used to identify novel and known mutations in RNA-seq data, automatically map, quantify, and annotate the transcriptomes, and compare the mutational patterns in the samples with the expression values of the corresponding transcripts and genes.

To run the ready-to-use workflow:

        Toolbox | Ready-to-Use Workflows | Whole Transcriptome Sequencing (Image rna_seq_group_closed_16_n_p) | (Human, Mouse or Rat) | Identify Variants and Add Expression Values (Image identify_variants_and_add_expression_values_wts_16_n_p)

  1. Double-click on the Identify Variants and Add Expression Values tool to start the analysis. If you are connected to a server, you will first be asked where you would like to run the analysis.

  2. Specify the RNA-seq reads to analyze. The reads can be selected by double-clicking on the reads file name or clicking once on the file and then clicking on the arrow pointing to the right side in the middle of the wizard (figure 17.23). Click Next.

    Image rnaseq_identify_variants_expression_step2
    Figure 17.23: Select the sequencing reads to analyze.

  3. Configure the parameters for the RNA-Seq Analysis (figure 17.24).

    Image wts7
    Figure 17.24: Configure the RNA-Seq Analysis. Here we specified a file for spike-in control but left the strand specific parameter to its default value.

    If you wish to use spike-in controls, add the relevant file in the "Spike-in controls" field.

    You can also specify that the reads should be mapped only in their forward or reverse orientation (it is by default set to both). Choosing to restrict mapping to one direction is typically appropriate when a strand specific protocol for read generation has been used, as it allows assignment of the reads to the right gene in cases where overlapping genes are located on different strands. Also, applying the 'strand specific' 'reverse' option in an RNA-seq run could allow the user to assess the degree of antisense transcription. Note that mate pairs are not supported when choosing the forward only or reverse only option.

    Click Next.

  4. Specify a target region for the Indels and Structural Variants tool (figure 17.25).

    Image wts8
    Figure 17.25: Specify the target region for the Indels and Structural Variants tool.

    The targeted region file is a file that specifies which regions have been sequenced. This file is something that you must provide yourself, as this file depends on the technology used for sequencing. You can obtain the targeted regions file from the vendor of your targeted sequencing reagents. Remember that you have a hg38-specific BED file when using hg38 as reference, and hg19-specific BED file when using hg19 as reference.

  5. Set the parameters for the Low Frequency Variant Detection step (see figure 17.26). For a description of the different parameters that can be adjusted in the variant detection step, see Low Frequency Variant Detection.

    Image wts9
    Figure 17.26: Specify the parametes for transcriptomic variant detection.

  6. If you are working with the workflow from the Human folder, specify here the relevant 1000 Genomes population (and HapMap populations at the next step) from the drop-down list (see figure 17.27). Choose the population that matches best the population your samples are derived from.

    Image wts10
    Figure 17.27: Select the relevant population from the drop-down list for 1000 Genomes and Hapmap databases.

    Under "Locked settings" you can see that "Automatically join adjacent MNVs and SNVs" has been selected. The reason for this is that many databases do not report a succession of SNVs as one MNV as is the case for the Biomedical Genomics Workbench, and as a consequence it is not possible to directly compare variants called with Biomedical Genomics Workbench with these databases. In order to support filtering against these databases anyway, the option to Automatically join adjacent MNVs and SNVs is enabled. This means that an MNV in the experimental data will get an exact match, if a set of SNVs and MNVs in the database can be combined to provide the same allele.

    Note: This assumes that SNVs and MNVs in the track of known variants represent the same allele, although there is no evidence for this in the track of known variants.

  7. Click Next to go to the last wizard step. Preview All Parameters allows you to preview all parameters but not edit them. Choose to save the results and click Finish.

Seven different output types are generated:

  1. Gene expression (Image rnaseqtrack_16_h_p) A track showing gene expression annotations. Hold the mouse over or right-clicking on the track. A tooltip will appear with information about e.g. gene name and expression values.
  2. Transcript expression (Image rnaseqtrack_16_h_p) A track showing transcript expression annotations. Hold the mouse over or right-clicking on the track. A tooltip will appear with information about e.g. gene name and expression values.
  3. RNA-Seq Mapping Report (Image proteinreport_16_n_p) This report contains information about the reads, reference, transcripts, and statistics. This is explained in more details here http://resources.qiagenbioinformatics.com/manuals/biomedicalgenomicsworkbench/current/index.php?manual=RNA_Seq_report.html.
  4. Read Mapping (Image read_track_16_n_p) The mapped RNA-seq reads. The RNA-seq reads are shown in different colors depending on their orientation, whether they are single reads or paired reads, and whether they map unambiguously. For the color codes please see Mapped reads coloring.

  5. Annotated Variants with Expression Values (Image variant_track_16_n_p) Annotation track showing the variants. Hold the mouse over one of the variants or right-clicking on the variant. A tooltip will appear with detailed information about the variant.
  6. RNA-Seq Genome Browser View (Image trackset_16_n_p) A collection of tracks presented together. Shows the annotated variants track together with the human reference sequence, genes, transcripts, coding regions, and variants detected in ClinVar and dbSNP (see figure 17.14).
  7. Log (Image table) A log of the workflow execution.